Disconnect power supply before making adjustments. Cords should be put in conduit or protected by placing planks alongside them. The grounded tool must have an approved 3-wire cord with a 3-prong plug. Unplug any cords to these outlets and do not use until a qualified electrician has checked the wiring. These injuries can come from direct contact with the electrical energy, electrical arcs that jumps to a person who is grounded, thermal burns including flash burns from heat generated by an electric arc, flame burns from materials that catch on fire from heating or ignition by electrical currents, and muscle contractions can cause a person to fall. Use extension cords only to temporarily supply power to an area that does not have a power outlet. This plug should be plugged in a properly grounded 3-pole outlet. Another common use for GFCI is for pools and hot tubs. Power tools used incorrectly can electrically hazardous. Halogen lamps can become very hot and may be a fire hazard. Replacing a fuse with one of a larger size can cause excessive currents in the wiring and possibly start a fire. Plug-in GFCIs can be plugged into wall outlets where appliances will be used and are commonly found in bathrooms. Electrical safety is simple. If the "RESET" button pops out but the light does not go out, the GFCI has been improperly wired and does not offer shock protection at that wall outlet. Keep power cords clear of tools during use. 2) Always tape cords to walls or floors when necessary. Do not tie power cords in tight knots; knots can cause short circuits and shocks. 4) Always use the correct size fuse. Many circuits are wired to twelve amp breakers so do not plug several extension cords into one outlet. Nails and staples can damage cords causing fire and shock hazards. Be aware and be safe. They can damage the insulation and cause a shock. Ensure tools are properly grounded or double-insulated. If the GFCI is working properly, the light should go out. Check power cords and plugs daily; discard if worn or damaged. A painful shock may occur during the time that it takes for the GFCI to cut off the electricity so it is important to use the GFCI as an extra protective measure rather than a replacement for safe work practices. A Ground Fault Circuit Interrupter (GFCI) works by detecting any loss of electrical current in a circuit. 9) Make sure that exposed receptacle boxes are made of non-conductive materials. 10) Know where the breakers and boxes are located in case of an emergency.
A GFCI Circuit Breaker can be installed on some circuit breaker electrical panels to protect an entire branch China Sprinklers suppliers circuit. 3) Use cords or equipment that is rated for the level of amperage or wattage that you are using. 11) Label all circuit breakers and fuse boxes clearly.In electrical injuries there are four main types of injuries: electrocution (will cause death), electric shock, burns, and falls. Switch tools OFF before connecting them to a power supply. The fall can cause serious injuries also. 12) Do not use outlets or cords that have exposed wiring or use power tools with the guards removed. 8) Risk of electric shock is greater in areas that are wet or damp.
Never use extension cords as permanent wiring. 6) Always use ladders made of wood or other non-conductive materials when working with or near electricity or power lines. Always disconnect the current first. High voltage contact burns can burn internal tissues while leaving only very small injuries on the outside of the skin. If not, have the GFCI repaired or replaced. GFCI wall outlets can be installed in place of standard outlets to protect against electrocution for just that outlet, or a series of outlets in the same branch. Install Ground Fault Circuit Interrupters, known also as GFCI, as they will interrupt the electrical circuit before a current sufficient to cause Quick connector death or serious injury occurs. Do not allow vehicles to pass over unprotected power cords. Contact a qualified electrician to correct any wiring errors. Do not block access to circuit breakers or fuse boxes and do not touch a person or electrical apparatus in the event of an electrical accident. When a loss is detected, the GFCI turns the electricity off before severe injuries or electrocution can occur. 7) Place halogen lights away from combustible materials such as cloths or curtains. Each switch should be positively identified as to which outlet or appliance it is for. Suspend power cords over aisles or work areas to eliminate stumbling or tripping hazards. Extension cords themselves can be hazardous. Keep power cords away from heat, water and oil. 5) Be aware that unusually warm or hot outlets may be a sign that unsafe wiring conditions exists.
Do not use electrical tools in wet conditions or damp locations unless tool is connected to a GFCI. Test the GFCI monthly. Electricity should be respected and precautions should be taken to prevent injuries. Repair or replace damaged equipment immediately. First plug a "night light" or lamp into the GFCI-protected wall outlet (the light should be turned on), then press the "TEST" button on the GFCI. There are some safeguard procedures that can be followed to ensure electrical safety: 1) Inspect tools, power cords, and electrical fittings for damage or wear prior to each use. The operation of power tools might ignite flammable substances and in can cause an explosion near certain vapors and gases. . Loop the cords or use a twist lock plug. Safety devises are becoming safer each year; its up to you to use them correctly. Reset the GFCI to restore power.
2017.12.25xukaimin